Linux version 2.4.29-ll-up-alt1 (builder@opteron.office.altlinux.ru) (gcc version 2.96 20000731 (ALT Linux, build 2.96-alt6)) #1 Thu Feb 24 18:35:27 MSK 2005
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000007fd0000 (usable)
 BIOS-e820: 0000000007fd0000 - 0000000007fdf000 (ACPI data)
 BIOS-e820: 0000000007fdf000 - 0000000007fe0000 (ACPI NVS)
 BIOS-e820: 0000000007fe0000 - 0000000008000000 (reserved)
 BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32720
zone(0): 4096 pages.
zone(1): 28624 pages.
zone(2): 0 pages.
DMI 2.2 present.
55 structures occupying 2372 bytes.
DMI table at 0x000F6CF0.
BIOS Vendor: IBM
BIOS Version: INET28WW
BIOS Release: 11/20/1999
System Vendor: IBM
Product Name: 26455BU
Version: Not Available
Serial Number: 78MFFD9
Board Vendor: IBM
Board Name: 26455BU
Board Version: Not Available
ACPI disabled because your bios is from 1999 and too old
You can enable it with acpi=force
IBM machine detected. Enabling interrupts during APM calls.
Kernel command line: BOOT_IMAGE=2429-ll-up-1 ro root=305
No local APIC present or hardware disabled
Initializing CPU#0
Detected 397.086 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 782.33 BogoMIPS
Memory: 126588k/130880k available (1350k kernel code, 3904k reserved, 508k data, 140k init, 0k highmem, 0k BadRAM)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0183f9ff 00000000 00000000 00000000
CPU:             Common caps: 0183f9ff 00000000 00000000 00000000
CPU: Intel Mobile Pentium II stepping 0a
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd880, last bus=7
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router PIIX/ICH [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
kinoded started
VFS: Disk quotas vdquot_6.5.1
vesafb: framebuffer at 0xe0000000, mapped to 0xc8800000, size 2496k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:a6c0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Looking for splash picture... no good signature found.
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xfcf0-0xfcf7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xfcf8-0xfcff, BIOS settings: hdc:DMA, hdd:pio
hda: C/H/S=0/0/3 from BIOS ignored
hda: IBM-DCXA-210000, ATA DISK drive
blk: queue c0321c60, I/O limit 4095Mb (mask 0xffffffff)
hdc: TOSHIBA DVD-ROM SD-C2102, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 19640880 sectors (10056 MB) w/420KiB Cache, CHS=19485/16/63, UDMA(33)
Partition check:
 hda: [PTBL] [1299/240/63] hda1 hda2 < hda5 hda6 hda7 >
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 53k freed
VFS: Mounted root (romfs filesystem) readonly.
VFS: Mounted root (ext2 filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 140k freed
Executing init=/sbin/init
Adding Swap: 362840k swap-space (priority -1)
Real Time Clock Driver v1.10f
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
subfs: subfs-2.4 version 0.9.
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 00:02.0
PCI: Sharing IRQ 11 with 00:06.0
PCI: Sharing IRQ 11 with 01:00.0
PCI: Found IRQ 11 for device 00:02.1
Yenta ISA IRQ mask 0x0698, PCI irq 11
Socket status: 30000006
Yenta ISA IRQ mask 0x0698, PCI irq 11
Socket status: 30000006
divert: not allocating divert_blk for non-ethernet device irlan0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
hdc: attached ide-cdrom driver.
hdc: ATAPI 20X DVD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
PCI: Found IRQ 11 for device 01:00.0
PCI: Sharing IRQ 11 with 00:02.0
PCI: Sharing IRQ 11 with 00:06.0
neofb: mapped io at c8b9e000
Panel is a 1024x768 color TFT display
neofb: frame buffer in use
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 18:44:13 Feb 24 2005
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0x8400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver