Linux version 2.6.16-wks26-up-alt3 (mutabor@Digitalina) (gcc version 3.4.5 20051201 (ALT Linux, build 3.4.5-alt4)) #2 PREEMPT Sat Sep 9 21:42:23 MSD 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 0000000008000000 (usable)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
128MB LOWMEM available.
On node 0 totalpages: 32768
  DMA zone: 4096 pages, LIFO batch:0
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 28672 pages, LIFO batch:7
  HighMem zone: 0 pages, LIFO batch:0
DMI 2.2 present.
ACPI: Unable to locate RSDP
Allocating PCI resources starting at 10000000 (gap: 08000000:f7ff0000)
Built 1 zonelists
Kernel command line: BOOT_IMAGE=2616-wks26-up-3 ro root=309
No local APIC present or hardware disabled
mapped APIC to ffffd000 (01101000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 523.910 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 126248k/131072k available (1470k kernel code, 4288k reserved, 594k data, 172k init, 0k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1049.40 BogoMIPS (lpj=524701)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 008021bf 808029bf 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 008021bf 808029bf 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: After all inits, caps: 008021bf 808029bf 00000000 00000002 00000000 00000000 00000000
CPU: AMD-K6(tm) 3D processor stepping 0c
Checking 'hlt' instruction... OK.
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 487k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb220, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbeb0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbed8, dseg 0xf0000
PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Using ALI M1533 IRQ Router
PCI: Using IRQ router ALI M1533 [10b9/1533] at 0000:00:07.0
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
pnp: 00:0a: ioport range 0x40b-0x40b has been reserved
pnp: 00:0a: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:0a: ioport range 0x5000-0x501f has been reserved
pnp: 00:0a: ioport range 0x4000-0x403f has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: e000-efff
  MEM window: d8000000-d9ffffff
  PREFETCH window: d4000000-d7ffffff
audit: initializing netlink socket (disabled)
audit(1157892890.545:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS3 at I/O 0x2e8 (irq = 3) is a 16550A
00:0c: ttyS3 at I/O 0x2e8 (irq = 3) is a 16550A
00:0f: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 12288K size 1024 blocksize
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
Using IPI Shortcut mode
Suspend2 Core.
Suspend2 Compression Driver loading.
Suspend2 Encryption Driver loading.
Suspend2 Swap Writer loading.
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (romfs filesystem) readonly.
input: AT Translated Set 2 keyboard as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:0f.0
ALI15X3: chipset revision 194
ALI15X3: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf400-0xf407, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xf408-0xf40f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD400PB-00EPA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: DV-516D, ATAPI CD/DVD-ROM drive
hdd: CD-W540E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78165360 sectors (40020 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(66)
hda: cache flushes supported
 hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 >
SCSI subsystem initialized
PCI: Found IRQ 10 for device 0000:00:0b.0
sym0: <810> rev 0x2 at pci 0000:00:0b.0 irq 10
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.2
  Vendor: QUANTUM   Model: VP32210           Rev: 81H8
  Type:   Direct-Access                      ANSI SCSI revision: 02
 target0:0:1: tagged command queuing enabled, command queue depth 16.
 target0:0:1: Beginning Domain Validation
 target0:0:1: asynchronous
 target0:0:1: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 8)
 target0:0:1: Domain Validation skipping write tests
 target0:0:1: Ending Domain Validation
SCSI device sda: 4308352 512-byte hdwr sectors (2206 MB)
sda: Write Protect is off
sda: Mode Sense: c8 00 10 08
SCSI device sda: drive cache: write back w/ FUA
SCSI device sda: 4308352 512-byte hdwr sectors (2206 MB)
sda: Write Protect is off
sda: Mode Sense: c8 00 10 08
SCSI device sda: drive cache: write back w/ FUA
 sda: sda1 sda2 < sda5 > sda3 sda4
sd 0:0:1:0: Attached scsi disk sda
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Suspend2 2.2.4: You need to use a resume2= command line parameter to tell Suspend2 where to look for an image.
Suspend2 2.2.4: Resume2 parameter is empty. Suspending will be disabled.
Suspend2 2.2.4: Missing or invalid storage location (resume2= parameter). Please correct and rerun lilo (or equivalent) before suspending.
XFS mounting filesystem hda9
Ending clean XFS mount for filesystem: hda9
VFS: Mounted root (xfs filesystem) readonly.
Trying to move old root to /initrd ... /initrd does not exist. Ignored.
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 172k freed
Executing init=/sbin/init
Adding 184736k swap on /dev/sda4.  Priority:-1 extents:1 across:184736k
Adding 1333352k swap on /dev/sda5.  Priority:-2 extents:1 across:1333352k
Real Time Clock Driver v1.12ac
hdc: ATAPI 16X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-cd: ignoring drive hdd
Linux agpgart interface v0.101 (c) Dave Jones
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
  Vendor: TEAC      Model: CD-W540E          Rev: 1.0C
  Type:   CD-ROM                             ANSI SCSI revision: 00
sr0: scsi-1 drive
sr 1:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:1:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
aty128fb: Found Intel x86 BIOS ROM Image
aty128fb: Rage128 BIOS located
aty128fb: Rage128 PF PRO AGP [chip rev 0x1] 16M 128-bit SDR SGRAM (1:1)
Console: switching to colour frame buffer device 80x30
fb0: ATY Rage128 frame buffer device on Rage128 PF PRO AGP
aty128fb: Rage128 MTRR set to ON
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
Supermount version 2.0.4 for kernel 2.6
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
cs4281: version v1.13.32 time 10:58:53 Sep 10 2006
PCI: Found IRQ 11 for device 0000:00:0a.0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Found IRQ 5 for device 0000:00:02.0
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 5, io mem 0xda011000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
input: PC Speaker as /class/input/input1
Floppy drive(s): fd0 is 1.44M, fd1 is 360K PC
FDC 0 is a post-1991 82077
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
input: GenPS/2 Genius Mouse as /class/input/input2
ts: Compaq touchscreen protocol output
agpgart: Detected ALi M1541 chipset
agpgart: AGP aperture is 64M @ 0xd0000000
usb 1-2: new full speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:02.0: Unlink after no-IRQ?  Controller is probably using the wrong IRQ.