Bootdata ok (command line is initrd=alt0/full.cz changedisk vga=0x314 showopts automatic=method:cdrom BOOT_IMAGE=alt0/vmlinuz ) Linux version 2.6.18-std-smp-alt3 (builder@int1.office.altlinux.org) (gcc version 4.1.1 20061011 (ALT Linux, build 4.1.1-alt10)) #1 SMP Fri Dec 22 22:42:05 MSK 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fee0000 (usable) BIOS-e820: 000000003fee0000 - 000000003fee3000 (ACPI NVS) BIOS-e820: 000000003fee3000 - 000000003fef0000 (ACPI data) BIOS-e820: 000000003fef0000 - 000000003ff00000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) DMI 2.4 present. ACPI: RSDP (v002 Nvidia ) @ 0x00000000000f7620 ACPI: XSDT (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fee30c0 ACPI: FADT (v003 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003feec480 ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x000000003feec680 ACPI: HPET (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000098) @ 0x000000003feec7c0 ACPI: MCFG (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003feec840 ACPI: MADT (v001 Nvidia ASUSACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003feec5c0 ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x03000000) @ 0x0000000000000000 Scanning NUMA topology in Northbridge 24 Number of nodes 1 Node 0 MemBase 0000000000000000 Limit 000000003fee0000 NUMA: Using 63 for the hash shift. Using node hash shift of 63 Bootmem setup node 0 0000000000000000-000000003fee0000 On node 0 totalpages: 257226 DMA zone: 2990 pages, LIFO batch:0 DMA32 zone: 254236 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:15 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Setting APIC routing to physical flat ACPI: HPET id: 0x10de8201 base: 0xfefff000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 40000000 (gap: 3ff00000:b0100000) SMP: Allowing 2 CPUs, 1 hotplug CPUs Built 1 zonelists. Total pages: 257226 Kernel command line: initrd=alt0/full.cz changedisk vga=0x314 showopts automatic=method:cdrom BOOT_IMAGE=alt0/vmlinuz Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) time.c: Using 25.000000 MHz WALL HPET GTOD HPET/TSC timer. time.c: Detected 1890.225 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Checking aperture... CPU 0: aperture @ 99c0000000 size 32 MB Aperture too small (32 MB) No AGP bridge found Memory: 1024336k/1047424k available (1845k kernel code, 22700k reserved, 1168k data, 192k init) Calibrating delay using timer specific routine.. 3784.22 BogoMIPS (lpj=7568447) Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 0/0 -> Node 0 SMP alternatives: switching to UP code checking if image is initramfs... it is Freeing initrd memory: 2859k freed ACPI: Core revision 20060707 ACPI: Looking for DSDT in initramfs... /DSDT.aml does not exist. Using local APIC timer interrupts. result 13126571 Detected 13.126 MHz APIC timer. Brought up 1 CPUs testing NMI watchdog ... OK. migration_cost=0 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at f0000000 PCI: No mmconfig possible on device 0:18 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Transparent bridge - 0000:00:06.0 Boot video device is 0000:07:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LAZA] (IRQs *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LSA2] (IRQs *5 7 9 10 11 14 15) ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report hpet0: at MMIO 0xfefff000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 31 hpet0: 3 32-bit timers, 25000000 Hz PCI-DMA: Disabling IOMMU. pnp: 00:01: ioport range 0x1000-0x107f could not be reserved pnp: 00:01: ioport range 0x1080-0x10ff has been reserved pnp: 00:01: ioport range 0x1400-0x147f has been reserved pnp: 00:01: ioport range 0x1480-0x14ff could not be reserved pnp: 00:01: ioport range 0x1800-0x187f has been reserved pnp: 00:01: ioport range 0x1880-0x18ff has been reserved PCI: Bridge: 0000:00:06.0 IO window: a000-afff MEM window: fde00000-fdefffff PREFETCH window: disabled. PCI: Bridge: 0000:00:0a.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0d.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0f.0 IO window: 9000-9fff MEM window: fa000000-fcffffff PREFETCH window: e0000000-efffffff PCI: Setting latency timer of device 0000:00:06.0 to 64 PCI: Setting latency timer of device 0000:00:0a.0 to 64 PCI: Setting latency timer of device 0000:00:0b.0 to 64 PCI: Setting latency timer of device 0000:00:0c.0 to 64 PCI: Setting latency timer of device 0000:00:0d.0 to 64 PCI: Setting latency timer of device 0000:00:0e.0 to 64 PCI: Setting latency timer of device 0000:00:0f.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered audit: initializing netlink socket (disabled) audit(1171237705.504:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Setting latency timer of device 0000:00:0a.0 to 64 pcie_portdrv_probe->Dev[0376:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0a.0:pcie00] Allocate Port Service[0000:00:0a.0:pcie03] PCI: Setting latency timer of device 0000:00:0b.0 to 64 pcie_portdrv_probe->Dev[0374:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0b.0:pcie00] Allocate Port Service[0000:00:0b.0:pcie03] PCI: Setting latency timer of device 0000:00:0c.0 to 64 pcie_portdrv_probe->Dev[0374:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0c.0:pcie00] Allocate Port Service[0000:00:0c.0:pcie03] PCI: Setting latency timer of device 0000:00:0d.0 to 64 pcie_portdrv_probe->Dev[0378:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0d.0:pcie00] Allocate Port Service[0000:00:0d.0:pcie03] PCI: Setting latency timer of device 0000:00:0e.0 to 64 pcie_portdrv_probe->Dev[0375:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0e.0:pcie00] Allocate Port Service[0000:00:0e.0:pcie03] PCI: Setting latency timer of device 0000:00:0f.0 to 64 pcie_portdrv_probe->Dev[0377:10de] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0f.0:pcie00] Allocate Port Service[0000:00:0f.0:pcie03] vesafb: framebuffer at 0xe0000000, mapped to 0xffffc20010100000, using 1875k, total 262144k vesafb: mode is 800x600x16, linelength=1600, pages=2 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 100x37 fb0: VESA VGA frame buffer device hpet_resources: 0xfefff000 is busy Linux agpgart interface v0.101 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered NET: Registered protocol family 1 ACPI: (supports S0 S1 S3 S4 S5) Freeing unused kernel memory: 192k freed Executing init=/init input: AT Translated Set 2 keyboard as /class/input/input0 usbcore: registered new driver usbfs usbcore: registered new driver hub ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23 GSI 16 sharing vector 0xE1 and IRQ 16 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 225 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: irq 225, io mem 0xfe02e000 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected usb 1-8: new high speed USB device using ehci_hcd and address 4 usb 1-8: configuration #1 chosen from 1 choice ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22 GSI 17 sharing vector 0xE9 and IRQ 17 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 22 (level, low) -> IRQ 233 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.0: irq 233, io mem 0xfe02f000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 10 ports detected usb 1-9: new high speed USB device using ehci_hcd and address 5 usb 1-9: configuration #1 chosen from 1 choice usb 2-2: new full speed USB device using ohci_hcd and address 2 usb 2-2: configuration #1 chosen from 1 choice usb 2-3: new low speed USB device using ohci_hcd and address 3 usb 2-3: configuration #1 chosen from 1 choice usbcore: registered new driver hiddev input: Logitech USB-PS/2 Optical Mouse as /class/input/input1 input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-3 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SCSI subsystem initialized NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0 NFORCE-MCP55: chipset revision 161 NFORCE-MCP55: not 100% native mode: will probe irqs later NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA Probing IDE interface ide0... hda: _NEC DVD_RW ND-4550A, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 libata version 2.00 loaded. sata_nv 0000:00:05.0: version 2.0 ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21 GSI 18 sharing vector 0x32 and IRQ 18 ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APSI] -> GSI 21 (level, low) -> IRQ 50 PCI: Setting latency timer of device 0000:00:05.0 to 64 ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xDC00 irq 50 ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xDC08 irq 50 scsi0 : sata_nv ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32) ata1.00: ata1: dev 0 multi count 1 ata1.00: configured for UDMA/133 scsi1 : sata_nv ata2: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0x977 Vendor: ATA Model: Hitachi HDT72502 Rev: V5DO Type: Direct-Access ANSI SCSI revision: 05 ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20 GSI 19 sharing vector 0x3A and IRQ 19 ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [APSJ] -> GSI 20 (level, low) -> IRQ 58 PCI: Setting latency timer of device 0000:00:05.1 to 64 ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC800 irq 58 ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC808 irq 58 scsi2 : sata_nv ata3: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0x9E7 scsi3 : sata_nv ata4: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0x967 ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [ASA2] -> GSI 23 (level, low) -> IRQ 225 PCI: Setting latency timer of device 0000:00:05.2 to 64 ata5: SATA max UDMA/133 cmd 0xC400 ctl 0xC002 bmdma 0xB400 irq 225 ata6: SATA max UDMA/133 cmd 0xBC00 ctl 0xB802 bmdma 0xB408 irq 225 scsi4 : sata_nv ata5: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0xC407 scsi5 : sata_nv ata6: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0xBC07 usbcore: registered new driver libusual Initializing USB Mass Storage driver... scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning scsi7 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning Vendor: GENERIC Model: USB Storage-SMC Rev: 016A Type: Direct-Access ANSI SCSI revision: 00 Vendor: GENERIC Model: USB Storage-CFC Rev: 016A Type: Direct-Access ANSI SCSI revision: 00 Vendor: GENERIC Model: USB Storage-MMC Rev: 016A Type: Direct-Access ANSI SCSI revision: 00 Vendor: GENERIC Model: USB Storage-MSC Rev: 016A Type: Direct-Access ANSI SCSI revision: 00 usb-storage: device scan complete Vendor: Kingston Model: DataTraveler 2.0 Rev: 1.00 Type: Direct-Access ANSI SCSI revision: 02 usb-storage: device scan complete ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A loop: loaded (max 8 devices) squashfs: version 3.1 (2006/08/19) Phillip Lougher Registering unionfs 1.4 unionfs: debugging is not enabled SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 6:0:0:0: Attached scsi generic sg1 type 0 scsi 6:0:0:1: Attached scsi generic sg2 type 0 scsi 6:0:0:2: Attached scsi generic sg3 type 0 scsi 6:0:0:3: Attached scsi generic sg4 type 0 scsi 7:0:0:0: Attached scsi generic sg5 type 0 SCSI device sda: drive cache: write back SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 < sda5 > sd 0:0:0:0: Attached scsi disk sda sd 6:0:0:0: Attached scsi removable disk sdb sd 6:0:0:1: Attached scsi removable disk sdc sd 6:0:0:2: Attached scsi removable disk sdd sd 6:0:0:3: Attached scsi removable disk sde SCSI device sdf: 2002944 512-byte hdwr sectors (1026 MB) sdf: Write Protect is off sdf: Mode Sense: 0b 00 00 08 sdf: assuming drive cache: write through SCSI device sdf: 2002944 512-byte hdwr sectors (1026 MB) sdf: Write Protect is off sdf: Mode Sense: 0b 00 00 08 sdf: assuming drive cache: write through sdf: sdf1 sd 7:0:0:0: Attached scsi removable disk sdf ts: Compaq touchscreen protocol output forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APCH] -> GSI 22 (level, low) -> IRQ 233 PCI: Setting latency timer of device 0000:00:08.0 to 64 forcedeth: using HIGHDMA input: PC Speaker as /class/input/input2 Bluetooth: Core ver 2.10 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Linux video capture interface: v2.00 eth0: forcedeth.c: subsystem: 01043:8239 bound to 0000:00:08.0 i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00 i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c40 gameport: EMU10K1 is pci0000:01:06.1/gameport0, io 0xa800, speed 1204kHz saa7130/34: v4l2 driver version 0.2.14 loaded ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 GSI 20 sharing vector 0x42 and IRQ 20 ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 66 saa7133[0]: found at 0000:01:08.0, rev: 240, irq: 66, latency: 32, mmio: 0xfdeff000 saa7133[0]: subsystem: 0000:4091, board: Beholder BeholdTV 409 FM [card=67,autodetected] saa7133[0]: board init: gpio is c0c000 input: saa7134 IR (Beholder BeholdTV 4 as /class/input/input3 Bluetooth: HCI USB driver ver 2.9 usbcore: registered new driver hci_usb saa7133[0]: i2c eeprom 00: 00 00 91 40 54 20 00 00 00 00 00 00 00 00 00 01 saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tuner 2-0043: chip found @ 0x86 (saa7133[0]) tda9887 2-0043: tda988[5/6/7] found @ 0x43 (tuner) tuner 2-0060: All bytes are equal. It is not a TEA5767 tuner 2-0060: chip found @ 0xc0 (saa7133[0]) tuner 2-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) saa7133[0]: registered device video0 [v4l2] saa7133[0]: registered device vbi0 saa7133[0]: registered device radio0