Bootdata ok (command line is BOOT_IMAGE=alt0/vmlinuz initrd=alt0/full.cz changedisk splash=silent vga=0x314 lang=ru_RU automatic=method:cdrom) Linux version 2.6.18-std-smp-alt12 (builder@apiary.armor.altlinux.org) (gcc version 4.1.1 20070105 (ALT Linux, build 4.1.1-alt12)) #1 SMP Mon Feb 11 00:44:57 MSK 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000097800 (usable) BIOS-e820: 0000000000097800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000cff70000 (usable) BIOS-e820: 00000000cff70000 - 00000000cff78000 (ACPI data) BIOS-e820: 00000000cff78000 - 00000000cff80000 (ACPI NVS) BIOS-e820: 00000000cff80000 - 00000000d0000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved) BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000130000000 (usable) DMI present. ACPI: RSDP (v000 PTLTD ) @ 0x00000000000f68a0 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x00000000cff73121 ACPI: FADT (v001 INTEL LINDHRST 0x06040000 PTL 0x00000003) @ 0x00000000cff77e38 ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x00000000cff77eac ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x00000000cff77f48 ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0x00000000cff77f70 ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x00000000cff77fc0 ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030224) @ 0x00000000cff7315d ACPI: DSDT (v001 Intel LINDHRST 0x06040000 MSFT 0x0100000e) @ 0x0000000000000000 No NUMA configuration found Faking a node at 0000000000000000-0000000130000000 Bootmem setup node 0 0000000000000000-0000000130000000 On node 0 totalpages: 1030314 DMA zone: 2946 pages, LIFO batch:0 DMA32 zone: 833448 pages, LIFO batch:31 Normal zone: 193920 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x06] enabled) Processor #6 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x07] enabled) Processor #7 15:4 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x03] address[0xfec80000] gsi_base[24]) IOAPIC[1]: apic_id 3, version 32, address 0xfec80000, GSI 24-47 ACPI: IOAPIC (id[0x04] address[0xfec80400] gsi_base[48]) IOAPIC[2]: apic_id 4, version 32, address 0xfec80400, GSI 48-71 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to physical flat Using ACPI (MADT) for SMP configuration information Nosave address range: 0000000000097000 - 0000000000098000 Nosave address range: 0000000000098000 - 00000000000a0000 Nosave address range: 00000000000a0000 - 00000000000e4000 Nosave address range: 00000000000e4000 - 0000000000100000 Nosave address range: 00000000cff70000 - 00000000cff78000 Nosave address range: 00000000cff78000 - 00000000cff80000 Nosave address range: 00000000cff80000 - 00000000d0000000 Nosave address range: 00000000d0000000 - 00000000e0000000 Nosave address range: 00000000e0000000 - 00000000f0000000 Nosave address range: 00000000f0000000 - 00000000fec00000 Nosave address range: 00000000fec00000 - 00000000fec10000 Nosave address range: 00000000fec10000 - 00000000fee00000 Nosave address range: 00000000fee00000 - 00000000fee01000 Nosave address range: 00000000fee01000 - 00000000ff800000 Nosave address range: 00000000ff800000 - 00000000ffc00000 Nosave address range: 00000000ffc00000 - 0000000100000000 Allocating PCI resources starting at d1000000 (gap: d0000000:10000000) SMP: Allowing 4 CPUs, 0 hotplug CPUs Built 1 zonelists. Total pages: 1030314 Kernel command line: BOOT_IMAGE=alt0/vmlinuz initrd=alt0/full.cz changedisk splash=silent vga=0x314 lang=ru_RU automatic=method:cdrom bootsplash: silent mode. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer. time.c: Detected 3200.202 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Checking aperture... PCI-DMA: Using software bounce buffering for IO (SWIOTLB) Placing software IO TLB between 0x58cc000 - 0x98cc000 Memory: 4044840k/4980736k available (1860k kernel code, 148468k reserved, 1212k data, 196k init) Calibrating delay using timer specific routine.. 6404.96 BogoMIPS (lpj=12809920) Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 256 CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K using mwait in idle threads. CPU: Physical Processor ID: 3 CPU: Processor Core ID: 0 CPU0: Thermal monitoring enabled (TM1) SMP alternatives: switching to UP code checking if image is initramfs... it is Freeing initrd memory: 4003k freed ACPI: Core revision 20060707 ACPI: Looking for DSDT in initramfs... /DSDT.aml does not exist. Using local APIC timer interrupts. result 12500711 Detected 12.500 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/4 APIC 0x0 Initializing CPU#1 Calibrating delay using timer specific routine.. 6400.80 BogoMIPS (lpj=12801612) CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU1: Thermal monitoring enabled (TM1) Intel(R) Xeon(TM) CPU 3.20GHz stepping 0a SMP alternatives: switching to SMP code Booting processor 2/4 APIC 0x1 Initializing CPU#2 Calibrating delay using timer specific routine.. 6400.70 BogoMIPS (lpj=12801418) CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU2: Thermal monitoring enabled (TM1) Intel(R) Xeon(TM) CPU 3.20GHz stepping 0a SMP alternatives: switching to SMP code Booting processor 3/4 APIC 0x7 Initializing CPU#3 Calibrating delay using timer specific routine.. 6400.90 BogoMIPS (lpj=12801816) CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 3 CPU: Processor Core ID: 0 CPU3: Thermal monitoring enabled (TM1) Intel(R) Xeon(TM) CPU 3.20GHz stepping 03 Brought up 4 CPUs testing NMI watchdog ... OK. migration_cost=15,1624 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at e0000000 PCI: No mmconfig possible on device 6:1 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 1180-11bf claimed by ICH4 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: PXH quirk detected, disabling MSI for SHPC device PCI: PXH quirk detected, disabling MSI for SHPC device Boot video device is 0000:06:01.0 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0.PXH0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0.PXH1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEY0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEZ0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 7 *10 11 14 15) ACPI: Device [PRT] status [0000000c]: functional but not present; setting present Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 12 devices PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI-GART: No AMD northbridge found. PCI: Bridge: 0000:01:00.0 IO window: 2000-2fff MEM window: dd200000-dd2fffff PREFETCH window: df200000-df2fffff PCI: Bridge: 0000:01:00.2 IO window: 3000-3fff MEM window: dd300000-dd3fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:02.0 IO window: 2000-3fff MEM window: dd100000-dd3fffff PREFETCH window: df200000-df2fffff PCI: Bridge: 0000:00:04.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:06.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: 4000-4fff MEM window: dd400000-deffffff PREFETCH window: d1000000-d10fffff GSI 16 sharing vector 0xA9 and IRQ 16 ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:02.0 to 64 PCI: Setting latency timer of device 0000:01:00.0 to 64 PCI: Setting latency timer of device 0000:01:00.2 to 64 ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:04.0 to 64 ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:06.0 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered Simple Boot Flag at 0x39 set to 0x1 audit: initializing netlink socket (disabled) audit(1205737527.196:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Setting latency timer of device 0000:00:02.0 to 64 Allocate Port Service[0000:00:02.0:pcie00] Allocate Port Service[0000:00:02.0:pcie01] PCI: Setting latency timer of device 0000:00:04.0 to 64 Allocate Port Service[0000:00:04.0:pcie00] Allocate Port Service[0000:00:04.0:pcie01] PCI: Setting latency timer of device 0000:00:06.0 to 64 Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie01] vesafb: framebuffer at 0xde000000, mapped to 0xffffc20010100000, using 3750k, total 8128k vesafb: mode is 800x600x16, linelength=1600, pages=7 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 146854 bytes,<6>...found (800x600, 27802 bytes, v3). Console: switching to colour frame buffer device 97x34 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac Linux agpgart interface v0.102 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered NET: Registered protocol family 1 ACPI: (supports S0 S1 S4 S5) Freeing unused kernel memory: 196k freed Executing init=/init input: AT Translated Set 2 keyboard as /class/input/input0 usbcore: registered new driver usbfs usbcore: registered new driver hub GSI 17 sharing vector 0xB1 and IRQ 17 ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 177 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 177, io mem 0xdd001000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 169, io base 0x00001400 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected GSI 18 sharing vector 0xB9 and IRQ 18 ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 185, io base 0x00001420 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected GSI 19 sharing vector 0xC1 and IRQ 19 ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 193 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 193, io base 0x00001440 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 169, io base 0x00001460 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb 2-1: new full speed USB device using uhci_hcd and address 2 irq 169: nobody cared (try booting with the "irqpoll" option) Call Trace: [] dump_stack+0x12/0x17 [] __report_bad_irq+0x30/0x7d [] note_interrupt+0x1e3/0x224 [] __do_IRQ+0xc7/0x105 [] do_IRQ+0xe7/0xf5 [] ret_from_intr+0x0/0xa DWARF2 unwinder stuck at ret_from_intr+0x0/0xa Leftover inexact backtrace: [] :usbcore:hcd_submit_urb+0x0/0x74f [] mwait_idle+0x36/0x4a [] cpu_idle+0x95/0xb8 [] start_kernel+0x220/0x225 [] _sinittext+0x288/0x28c handlers: [] (usb_hcd_irq+0x0/0x55 [usbcore]) [] (usb_hcd_irq+0x0/0x55 [usbcore]) Disabling IRQ #169 usb 2-1: configuration #1 chosen from 1 choice usb 2-2: new low speed USB device using uhci_hcd and address 3 usb 2-2: configuration #1 chosen from 1 choice usbcore: registered new driver hiddev input: A4Tech USB Optical Mouse as /class/input/input1 input: USB HID v1.10 Mouse [A4Tech USB Optical Mouse] on usb-0000:00:1d.0-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SCSI subsystem initialized ICH5: IDE controller at PCI slot 0000:00:1f.1 ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 193 ICH5: chipset revision 2 ICH5: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x14a0-0x14a7, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x14a8-0x14af, BIOS settings: hdc:pio, hdd:DMA Probing IDE interface ide0... Probing IDE interface ide1... hdd: MATSHITADVD-ROM SR-8178, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hdd: ATAPI 24X DVD-ROM drive, 256kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 usbcore: registered new driver libusual Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new driver usb-storage USB Mass Storage support registered. Vendor: Generic Model: Flash Disk Rev: 7.77 Type: Direct-Access ANSI SCSI revision: 02 usb-storage: device scan complete ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A loop: loaded (max 8 devices) squashfs: version 3.3 (2007/10/31) Phillip Lougher Registering unionfs 1.4 unionfs: debugging is not enabled input: PC Speaker as /class/input/input2 Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 ts: Compaq touchscreen protocol output GSI 20 sharing vector 0xC9 and IRQ 20 ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 201 Intel(R) PRO/1000 Network Driver - version 7.2.7-k2-NAPI Copyright (c) 1999-2006 Intel Corporation. GSI 21 sharing vector 0xD1 and IRQ 21 ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 54 (level, low) -> IRQ 209 SCSI device sda: 512000 512-byte hdwr sectors (262 MB) e1000: 0000:03:02.0: e1000_probe: (PCI-X:133MHz:64-bit) 00:30:48:2f:0b:e0 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection GSI 22 sharing vector 0xD9 and IRQ 22 ACPI: PCI Interrupt 0000:03:02.1[B] -> GSI 55 (level, low) -> IRQ 217 e1000: 0000:03:02.1: e1000_probe: (PCI-X:133MHz:64-bit) 00:30:48:2f:0b:e1 e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection sda: Write Protect is off sda: Mode Sense: 03 00 00 00 sda: assuming drive cache: write through SCSI device sda: 512000 512-byte hdwr sectors (262 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 00 sda: assuming drive cache: write through sda: sda1 sd 0:0:0:0: Attached scsi removable disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 mtrr: type mismatch for de7e0000,10000 old: uncachable new: write-combining mtrr: type mismatch for de7c0000,20000 old: uncachable new: write-combining mtrr: type mismatch for de780000,40000 old: uncachable new: write-combining mtrr: type mismatch for de700000,80000 old: uncachable new: write-combining mtrr: type mismatch for de600000,100000 old: uncachable new: write-combining mtrr: type mismatch for de400000,200000 old: uncachable new: write-combining mtrr: type mismatch for de000000,400000 old: uncachable new: write-combining aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.2 loaded