live-20070529 намертво виснет на шаге "Populating /dev ..." Мандрива 2007 на этой машине работает нормально. $ lspci -v 00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03) Flags: bus master, medium devsel, latency 0 Memory at d0000000 (32-bit, prefetchable) [size=128M] Capabilities: [a0] AGP version 2.0 Capabilities: [c0] Power Management version 2 00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] PCI Bridge (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, medium devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: e8000000-e9ffffff Prefetchable memory behind bridge: d8000000-e7ffffff Capabilities: [80] Power Management version 2 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40) Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge Flags: bus master, stepping, medium devsel, latency 0 Capabilities: [c0] Power Management version 2 00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE Flags: bus master, medium devsel, latency 32 I/O ports at a000 [size=16] Capabilities: [c0] Power Management version 2 00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller Flags: bus master, medium devsel, latency 32, IRQ 7 I/O ports at a400 [size=32] Capabilities: [80] Power Management version 2 00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1a) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller Flags: bus master, medium devsel, latency 32, IRQ 7 I/O ports at a800 [size=32] Capabilities: [80] Power Management version 2 00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40) Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] Flags: medium devsel, IRQ 9 Capabilities: [68] Power Management version 2 00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 50) Subsystem: VIA Technologies, Inc. Onboard Audio on EP7KXA Flags: medium devsel, IRQ 3 I/O ports at ac00 [size=256] I/O ports at b000 [size=4] I/O ports at b400 [size=4] Capabilities: [c0] Power Management version 2 00:0b.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller Flags: bus master, medium devsel, latency 32, IRQ 3 I/O ports at b800 [size=32] Capabilities: [80] Power Management version 2 00:0b.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 61) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller Flags: bus master, medium devsel, latency 32, IRQ 7 I/O ports at bc00 [size=32] Capabilities: [80] Power Management version 2 00:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63) (prog-if 20 [EHCI]) Subsystem: VIA Technologies, Inc. USB 2.0 Flags: bus master, medium devsel, latency 32, IRQ 11 Memory at eb001000 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RT8139 Flags: bus master, medium devsel, latency 32, IRQ 11 I/O ports at c000 [size=256] Memory at eb000000 (32-bit, non-prefetchable) [size=256] [virtual] Expansion ROM at 30000000 [disabled] [size=64K] Capabilities: [50] Power Management version 2 00:11.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) Subsystem: Avermedia Technologies Inc AverMedia UltraTV PCI 350 Flags: bus master, medium devsel, latency 32, IRQ 11 Memory at eb002000 (32-bit, prefetchable) [size=4K] Capabilities: [44] Vital Product Data Capabilities: [4c] Power Management version 2 00:11.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) Subsystem: Avermedia Technologies Inc UltraTV PCI 350 Flags: bus master, medium devsel, latency 32, IRQ 11 Memory at eb003000 (32-bit, prefetchable) [size=4K] Capabilities: [44] Vital Product Data Capabilities: [4c] Power Management version 2 00:12.0 Multimedia video controller: Zoran Corporation ZR36057PQC Video cutting chipset (rev 02) Subsystem: Miro Computer Products AG DC10 Plus Flags: bus master, fast devsel, latency 32, IRQ 10 Memory at eb004000 (32-bit, non-prefetchable) [size=4K] 00:14.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 0a) Subsystem: Creative Labs SBLive! 5.1 eMicro 28028 Flags: bus master, medium devsel, latency 32, IRQ 7 I/O ports at c400 [size=32] Capabilities: [dc] Power Management version 1 00:14.1 Input device controller: Creative Labs SB Live! Game Port (rev 0a) Subsystem: Creative Labs Gameport Joystick Flags: bus master, medium devsel, latency 32 I/O ports at c800 [size=8] Capabilities: [dc] Power Management version 1 01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200] (rev 01) (prog-if 00 [VGA]) Subsystem: C.P. Technology Co. Ltd Unknown device 2063 Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11 Memory at d8000000 (32-bit, prefetchable) [size=128M] I/O ports at 9000 [size=256] Memory at e9000000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at e8000000 [disabled] [size=128K] Capabilities: [58] AGP version 2.0 Capabilities: [50] Power Management version 2 01:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200] (Secondary) (rev 01) Subsystem: C.P. Technology Co. Ltd Unknown device 2062 Flags: bus master, 66MHz, medium devsel, latency 32 Memory at e0000000 (32-bit, prefetchable) [size=128M] Memory at e9010000 (32-bit, non-prefetchable) [size=64K] Capabilities: [50] Power Management version 2
$ cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 6 model : 8 model name : Athlon XP (Tbre stepping : 1 cpu MHz : 1666.390 cache size : 256 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dn bogomips : 3336.06 Вывод lsusb -vvv: http://sciencefit.narod.ru/DDmach/lsusb
На Desktop 4.0 или новее часом не пробовали?
Пробовали ... Увы, хозяин проблемной машины "не находит времени" конкретно поискать причину: повытаскивать платки из pci-слотов :(
Причина оказалась в плате видеозахвата Pinnacle Studio DC10+, чипсет ZORAN. Убрали плату - заработало. С этой платой ни ALT 4.0 (Live), ни Knoppix (3.7) не работают, виснут на "populating dev". Мандрива, однако, работает ;) Версию ALT Linux 4.0.2 пока не пробовали
С livecd проверять неудобно - хорошо бы иметь установленную обычным образом систему, где можно провести следующие проверки: 1) Вписать в /etc/modprobe.d/blacklist-local строку: blacklist zr36067 После этого, вероятнее всего, удастся загрузить систему обычным образом при вставленной проблемной плате, поскольку её драйвер не будет загружаться автоматически. В этом состоянии нужно снять вывод dmesg и lspci -vvnn. 2) Вставить проблемную плату, загрузить систему с опцией init=/sbin/sash (вместо нормальной загрузки запустится shell даже без перемонтирования корня в rw, так что зависание ничего не испортит), после чего попробовать выполнить dmesg -n8 modprobe zr36067 debug=4 Если в результате система не зависнет (что маловероятно, но возможно), можно сохранить сообщения ядра и перезагрузить систему для последующей загрузки в обычном режиме: mount -o rw,remount / dmesg > /root/dmesg.log mount -o ro,remount / reboot -f В случае зависания придётся фотографировать/переписывать отладочные сообщения с экрана. Кроме того, имеет смысл попробовать вставить эту плату в другую машину, чтобы определить, связано ли зависание с особенностями именно этой машины (чипсет, BIOS, ...).
Смена мат. платы не помогла (правда, новая мат. плата тоже VIA)
(In reply to comment #5) > С livecd проверять неудобно - хорошо бы иметь установленную обычным образом > систему, где можно провести следующие проверки: > > 1) Вписать в /etc/modprobe.d/blacklist-local строку: > > blacklist zr36067 > > После этого, вероятнее всего, удастся загрузить систему обычным образом при Не удалось. Загрузка застряла на... sound.r* ... что-то вроде этого. Только полностью вынув плату загрузил Альт. > автоматически. В этом состоянии нужно снять вывод dmesg и lspci -vvnn. Надо? Без платы. > 2) Вставить проблемную плату, загрузить систему с опцией init=/sbin/sash (вместо > dmesg -n8 > modprobe zr36067 debug=4 > > Если в результате система не зависнет (что маловероятно, но возможно), НЕ ЗАВИСЛА!!!!! С ПЛАТОЙ!!!! > сохранить сообщения ядра и перезагрузить систему для последующей > обычном режиме: > > mount -o rw,remount / > dmesg > /root/dmesg.log > mount -o ro,remount / > reboot -f Вот dmesg.log: Linux version 2.6.18-std-smp-alt10 (builder@apiary.armor.altlinux.org) (gcc version 4.1.1 20070105 (ALT Linux, build 4.1.1-alt12)) #1 SMP Wed Dec 12 23:42:05 MSK 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. On node 0 totalpages: 131056 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 126960 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v000 KT266 ) @ 0x000f7570 ACPI: RSDT (v001 KT266 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000 ACPI: FADT (v001 KT266 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040 ACPI: DSDT (v001 KT266 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000 ACPI: PM-Timer IO Port: 0x4008 Allocating PCI resources starting at 30000000 (gap: 20000000:dfff0000) Detected 1674.000 MHz processor. Built 1 zonelists. Total pages: 131056 Kernel command line: auto BOOT_IMAGE=ALTLinux ro root=UUID=6c7eb358-ad93-49d2-8a05-299de9d03fee resume=/dev/hdc6 panic=30 splash=silent init=/sbin/sash bootsplash: silent mode. Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (0140a000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 515668k/524224k available (1590k kernel code, 8040k reserved, 639k data, 192k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3350.86 BogoMIPS (lpj=6701725) Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383f9ff c1c3f9ff 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383f9ff c1c3f9ff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0383f9ff c1c3f9ff 00000000 00000420 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 12k freed checking if image is initramfs... it is Freeing initrd memory: 373k freed ACPI: Core revision 20060707 ACPI: Looking for DSDT in initramfs... /DSDT.aml does not exist. ACPI: setting ELCR to 0200 (from 0e08) CPU0: AMD Athlon(tm) stepping 01 SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs migration_cost=0 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb470, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 1 *3 4 5 6 7 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:01.0 IO window: 9000-9fff MEM window: e8000000-e9ffffff PREFETCH window: d8000000-e7ffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered audit: initializing netlink socket (disabled) audit(1201708197.644:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) vesafb: framebuffer at 0xd8000000, mapped to 0xe0880000, using 3750k, total 131072k vesafb: mode is 800x600x16, linelength=1600, pages=135 vesafb: protected mode interface info at c000:56d3 vesafb: pmi: set display start = c00c5767, set palette = c00c57b3 vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 57947 bytes,<6>...found (800x600, 12886 bytes, v3). Console: switching to colour frame buffer device 97x34 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered NET: Registered protocol family 1 Using IPI No-Shortcut mode ACPI: (supports S0 S1 S4 S5) Time: tsc clocksource has been installed. Freeing unused kernel memory: 192k freed Executing init=/init input: AT Translated Set 2 keyboard as /class/input/input0 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:11.1 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 PCI: VIA IRQ fixup for 0000:00:11.1, from 255 to 10 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8233a (rev 00) IDE UDMA133 controller on pci0000:00:11.1 ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: ST3160812A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hda: max request size: 512KiB hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hdc: ST380021A, ATA DISK drive hdd: BENQ DVD DD DW1620, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hdc: max request size: 128KiB hdc: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100) hdc: cache flushes not supported hdc: hdc1 hdc2 hdc3 < hdc5 hdc6 hdc7 > Attempting manual resume kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Linux video capture interface: v2.00 Linux video codec intermediate layer: v0.2 Zoran MJPEG board driver version 0.9.5 ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 MJPEG[0]: Zoran ZR36067 (rev 2) irq: 11, memory: 0xeb003000 MJPEG[0]: subsystem vendor=0x1031 id=0x7efe MJPEG[0]: find_zr36057() - trying to autodetect card type MJPEG[0]: find_zr36057() - card DC10plus detected DC10plus[0]: Initializing i2c bus... DC10plus[0]: i2c_client_register() - driver id = 22 DC10plus[0]: i2c_client_register() - driver id = 48 DC10plus[0]: Initializing videocodec bus... DC10plus[0]: jpeg_codec_sleep() - sleep GPIO=0x81008888 DC10plus[0]: jpeg_codec_sleep() - wake GPIO=0x89008888 ZORAN: 1 card(s) found DC10plus[0]: zr36057_init() - initializing card[0], zr=e0da2d40 DC10plus[0]: check_jpg_settings() - dec: 1, Hdcm: 0, Vdcm: 0, Tdcm: 0 DC10plus[0]: check_jpg_settings() - x: 0, y: 0, w: 0, y: 0 DC10plus[0]: dc10plus_init() DC10plus[0]: jpeg_codec_sleep() - sleep GPIO=0x81008888 DC10plus[0]: jpeg_codec_sleep() - wake GPIO=0x89008888 DC10plus[0]: jpeg_codec_sleep() - wake GPIO=0xc9008888 DC10plus[0]: jpeg_codec_sleep() - sleep GPIO=0xc1008888 DC10plus[0]: enable_jpg(IDLE) DC10plus[0]: Guests: 0x10 0x10 0x10 0x10 0x10 0x10 0x11 DC10plus[0]: Detecting guests activity, please wait... DC10plus[0]: Guests: 0x10 0x10 0x10 0x10 0x10 0x10 0x10 DC10plus[0]: 8957: 7 => 0x12 DC10plus[0]: 417: 7 => 0x11 DC10plus[0]: 19592: 7 => 0x13 DC10plus[0]: 397: 7 => 0x10 DC10plus[0]: 19592: 7 => 0x12 DC10plus[0]: 417: 7 => 0x11 DC10plus[0]: 19592: 7 => 0x13 DC10plus[0]: 417: 7 => 0x10 DC10plus[0]: interrupts received: GIRQ1:51 queue_state=0/0/0/0 DC10plus[0]: procfs entry /proc/zoran0 allocated. data=e0da2d40 EXT3 FS on hdc2, internal journal > Кроме того, имеет смысл попробовать вставить эту плату в другую машину, чтобы > определить, связано ли зависание с особенностями именно этой машины > (чипсет, BIOS, ...). Собственно началось все на DFI AK-75EC (VIA KT-133-a) продолжается это на Jetway VIA KT-266-a.
Думаю что пробелма давно исчезла
Нет. Принесли в жертву одну из плат.
