После установки kernel-image-2.6.24-alt6 обнаружилась масса проблем (ACPI, Bluetooth и saa7134-alsa). dmesg после загрузки ниже: Linux version 2.6.24-std-def-alt6 (builder@apiary.armor.altlinux.org) (gcc version 4.1.2 20070626 (ALT Linux, build 4.1.2-alt2)) #1 SMP Tue Mar 25 18:48:39 MSK 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000005ffb0000 (usable) BIOS-e820: 000000005ffb0000 - 000000005ffbe000 (ACPI data) BIOS-e820: 000000005ffbe000 - 000000005ffe0000 (ACPI NVS) BIOS-e820: 000000005ffe0000 - 0000000060000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved) 639MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000ff780 Entering add_active_range(0, 0, 393136) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 393136 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 393136 On node 0 totalpages: 393136 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 1279 pages used for memmap HighMem zone: 162481 pages, LIFO batch:31 Movable zone: 0 pages used for memmap DMI 2.3 present. ACPI: RSDP 000FB650, 0014 (r0 ACPIAM) ACPI: RSDT 5FFB0000, 0034 (r1 A M I OEMRSDT 9000513 MSFT 97) ACPI: FACP 5FFB0200, 0084 (r2 A M I OEMFACP 9000513 MSFT 97) ACPI: DSDT 5FFB0450, 7BFA (r1 A0350 A0350001 1 INTL 2002026) ACPI: FACS 5FFBE000, 0040 ACPI: APIC 5FFB0390, 0080 (r1 A M I OEMAPIC 9000513 MSFT 97) ACPI: MCFG 5FFB0410, 003C (r1 A M I OEMMCFG 9000513 MSFT 97) ACPI: OEMB 5FFBE040, 005B (r1 A M I AMI_OEM 9000513 MSFT 97) Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override ACPI: PM-Timer IO Port: 0x508 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 70000000 (gap: 60000000:9ec00000) swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e4000 swsusp: Registered nosave memory region: 00000000000e4000 - 0000000000100000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 390065 Kernel command line: auto BOOT_IMAGE=2624-std-def-6 ro root=805 mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 3400.243 MHz processor. spurious 8259A interrupt: IRQ7. Console: colour dummy device 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1553736k/1572544k available (2199k kernel code, 17604k reserved, 795k data, 312k init, 655040k highmem) virtual kernel memory layout: fixmap : 0xffe13000 - 0xfffff000 (1968 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc03f4000 - 0xc0442000 ( 312 kB) .data : 0xc0325c3c - 0xc03eca44 ( 795 kB) .text : 0xc0100000 - 0xc0325c3c (2199 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 6805.94 BogoMIPS (lpj=13611892) Security Framework initialized Capability LSM initialized Mount-cache hash table entries: 512 Initializing cgroup subsys ns Initializing cgroup subsys cpuacct CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000649d 00000000 00000000 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 20000000 00000000 0000b180 0000649d 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (24) available CPU0: Thermal monitoring enabled Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20070126 CPU0: Intel(R) Pentium(R) 4 CPU 3.40GHz stepping 03 SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 6800.78 BogoMIPS (lpj=13601579) CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000649d 00000000 00000000 00000000 monitor/mwait feature present. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 20000000 00000000 0000b180 0000649d 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (24) available CPU1: Thermal monitoring enabled CPU1: Intel(R) Pentium(R) 4 CPU 3.40GHz stepping 03 Total of 2 processors activated (13606.73 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs CPU0 attaching sched-domain: domain 0: span 00000003 groups: 00000001 00000002 domain 1: span 00000003 groups: 00000003 CPU1 attaching sched-domain: domain 0: span 00000003 groups: 00000002 00000001 domain 1: span 00000003 groups: 00000003 net_namespace: 64 bytes Booting paravirtualized kernel on bare hardware NET: Registered protocol family 16 ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=10 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: EC: Look up EC in DSDT ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.LSTA] (Node f7c34cd0), AE_TYPE ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.LATA._STA] (Node f7c36d60), AE_TYPE ACPI Error (uteval-0233): Method execution failed [\_SB_.LATA._STA] (Node f7c36d60), AE_TYPE ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.LSTA] (Node f7c34cd0), AE_TYPE ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.LATA._STA] (Node f7c36d60), AE_TYPE ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Transparent bridge - 0000:00:12.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PA._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PB._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PD._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PE._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PF._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *11 ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *11 ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *11 ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *11 ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *11 ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *3 ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *11 ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *11 ACPI: PCI Interrupt Link [LMC9] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *10 ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *11 ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *11 ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 3C, should be 0E [20070126] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.LSTA] (Node f7c34cd0), AE_TYPE ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.LATA._STA] (Node f7c36d60), AE_TYPE ACPI Error (uteval-0233): Method execution failed [\_SB_.LATA._STA] (Node f7c36d60), AE_TYPE pnp: PnP ACPI: found 17 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default ACPI: RTC can wake from S4 Time: tsc clocksource has been installed. system 00:09: ioport range 0x4d0-0x4d1 has been reserved system 00:09: ioport range 0x800-0x80f has been reserved system 00:09: ioport range 0x500-0x57f has been reserved system 00:09: ioport range 0x580-0x5ff has been reserved system 00:09: ioport range 0x900-0x97f has been reserved system 00:09: ioport range 0x980-0x9ff has been reserved system 00:09: ioport range 0xe00-0xe7f has been reserved system 00:09: ioport range 0xe80-0xeff has been reserved system 00:09: iomem range 0xfee01000-0xfeefffff could not be reserved system 00:09: iomem range 0xfefff000-0xfeffffff has been reserved system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved system 00:0e: ioport range 0xc00-0xc0f has been reserved system 00:0e: ioport range 0xd00-0xd0f has been reserved system 00:0e: ioport range 0xa20-0xa2f has been reserved system 00:0e: ioport range 0xa30-0xa3f has been reserved system 00:0f: iomem range 0xe0000000-0xefffffff has been reserved system 00:10: iomem range 0x0-0x9ffff could not be reserved system 00:10: iomem range 0xc0000-0xcffff could not be reserved system 00:10: iomem range 0xe0000-0xfffff could not be reserved system 00:10: iomem range 0x100000-0x5fffffff could not be reserved system 00:10: iomem range 0x0-0x0 could not be reserved PCI: Bridge: 0000:00:02.0 IO window: disabled. MEM window: f4600000-fe6fffff PREFETCH window: cff00000-dfefffff PCI: Bridge: 0000:00:04.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:05.0 IO window: 9000-9fff MEM window: fe700000-fe8fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:06.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:07.0 IO window: a000-afff MEM window: fe900000-fe9fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:12.0 IO window: disabled. MEM window: fea00000-feafffff PREFETCH window: disabled. PCI: Bridge: 0000:00:14.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:15.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:16.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:17.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:02.0 to 64 PCI: Setting latency timer of device 0000:00:04.0 to 64 PCI: Setting latency timer of device 0000:00:05.0 to 64 PCI: Setting latency timer of device 0000:00:06.0 to 64 PCI: Setting latency timer of device 0000:00:07.0 to 64 PCI: Setting latency timer of device 0000:00:12.0 to 64 PCI: Setting latency timer of device 0000:00:14.0 to 64 PCI: Setting latency timer of device 0000:00:15.0 to 64 PCI: Setting latency timer of device 0000:00:16.0 to 64 PCI: Setting latency timer of device 0000:00:17.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 537k freed audit: initializing netlink socket (disabled) audit(1206652996.560:1): initialized highmem bounce pool size: 64 pages Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Found disabled HT MSI Mapping on 0000:00:14.0 PCI: MSI quirk detected. MSI disabled on chipset 0000:00:14.0. PCI: Found disabled HT MSI Mapping on 0000:00:15.0 PCI: MSI quirk detected. MSI disabled on chipset 0000:00:15.0. PCI: Found disabled HT MSI Mapping on 0000:00:16.0 PCI: MSI quirk detected. MSI disabled on chipset 0000:00:16.0. PCI: Found disabled HT MSI Mapping on 0000:00:17.0 PCI: MSI quirk detected. MSI disabled on chipset 0000:00:17.0. Boot video device is 0000:01:00.0 PCI: Setting latency timer of device 0000:00:02.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:02.0:pcie00] PCI: Setting latency timer of device 0000:00:04.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:04.0:pcie00] PCI: Setting latency timer of device 0000:00:05.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:05.0:pcie00] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] PCI: Setting latency timer of device 0000:00:07.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:07.0:pcie00] PCI: Setting latency timer of device 0000:00:14.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:14.0:pcie00] PCI: Setting latency timer of device 0000:00:15.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:15.0:pcie00] PCI: Setting latency timer of device 0000:00:16.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:16.0:pcie00] PCI: Setting latency timer of device 0000:00:17.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:17.0:pcie00] vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 11484k, total 131072k vesafb: mode is 1400x1050x16, linelength=2800, pages=1 vesafb: protected mode interface info at c000:d6b0 vesafb: pmi: set display start = c00cd6e6, set palette = c00cd750 vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 175x65 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize input: Macintosh mouse button emulation as /class/input/input0 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice cpuidle: using governor ladder cpuidle: using governor menu TCP bic registered NET: Registered protocol family 1 Using IPI No-Shortcut mode registered taskstats version 1 Freeing unused kernel memory: 312k freed Executing init=/init input: AT Translated Set 2 keyboard as /class/input/input1 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE-CK804: IDE controller (0x10de:0x0053 rev 0xf3) at PCI slot 0000:00:0f.0 NFORCE-CK804: not 100% native mode: will probe irqs later NFORCE-CK804: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE-CK804: 0000:00:0f.0 (rev f3) UDMA133 controller ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... Probing IDE interface ide1... hdc: TEAC DV-W518GM, ATAPI CD/DVD-ROM drive hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4 hdc: UDMA/66 mode selected ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide0... SCSI subsystem initialized Driver 'sd' needs updating - please use bus_type methods libata version 3.00 loaded. ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:10.0 to 64 ACPI: PCI interrupt for device 0000:00:10.0 disabled ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LSA1] -> GSI 22 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:11.0 to 64 ACPI: PCI interrupt for device 0000:00:11.0 disabled sata_nv 0000:00:10.0: version 3.5 ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LSA0] -> GSI 23 (level, low) -> IRQ 16 sata_nv 0000:00:10.0: Using ADMA mode PCI: Setting latency timer of device 0000:00:10.0 to 64 scsi0 : sata_nv scsi1 : sata_nv ata1: SATA max UDMA/133 cmd 0xcc00 ctl 0xc880 bmdma 0xc400 irq 16 ata2: SATA max UDMA/133 cmd 0xc800 ctl 0xc480 bmdma 0xc408 irq 16 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-7: ST3808110AS, 3.AAD, max UDMA/133 ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-7: ST3120813AS, 3.AAD, max UDMA/133 ata2.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32) ata2.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA ST3808110AS 3.AA PQ: 0 ANSI: 5 ata1: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda4 < sda5 sda6 > sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: Direct-Access ATA ST3120813AS 3.AA PQ: 0 ANSI: 5 ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 sd 1:0:0:0: [sdb] 234441648 512-byte hardware sectors (120034 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 1:0:0:0: [sdb] 234441648 512-byte hardware sectors (120034 MB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sd 1:0:0:0: [sdb] Attached SCSI disk ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LSA1] -> GSI 22 (level, low) -> IRQ 17 sata_nv 0000:00:11.0: Using ADMA mode PCI: Setting latency timer of device 0000:00:11.0 to 64 scsi2 : sata_nv scsi3 : sata_nv ata3: SATA max UDMA/133 cmd 0xc080 ctl 0xc000 bmdma 0xb800 irq 17 ata4: SATA max UDMA/133 cmd 0xbc00 ctl 0xb880 bmdma 0xb808 irq 17 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata4.00: ATA-7: ST3400620AS, 3.AAK, max UDMA/133 ata4.00: 781422768 sectors, multi 16: LBA48 NCQ (depth 31/32) ata4.00: configured for UDMA/133 scsi 3:0:0:0: Direct-Access ATA ST3400620AS 3.AA PQ: 0 ANSI: 5 ata4: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 sd 3:0:0:0: [sdc] 781422768 512-byte hardware sectors (400088 MB) sd 3:0:0:0: [sdc] Write Protect is off sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdc] 781422768 512-byte hardware sectors (400088 MB) sd 3:0:0:0: [sdc] Write Protect is off sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc1 sdc2 sd 3:0:0:0: [sdc] Attached SCSI disk sata_sil24 0000:03:00.0: version 1.1 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 19 ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKB] -> GSI 19 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:03:00.0 to 64 scsi4 : sata_sil24 scsi5 : sata_sil24 ata5: SATA max UDMA/100 host m128@0xfe8ffc00 port 0xfe8f8000 irq 18 ata6: SATA max UDMA/100 host m128@0xfe8ffc00 port 0xfe8fa000 irq 18 ata5: SATA link down (SStatus 0 SControl 0) ata6: SATA link down (SStatus 0 SControl 0) ReiserFS: sda5: found reiserfs format "3.6" with standard journal ReiserFS: sda5: using ordered data mode ReiserFS: sda5: journal params: device sda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda5: checking transaction log (sda5) ReiserFS: sda5: Using r5 hash to sort names fuse init (API version 7.9) sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: Attached scsi generic sg1 type 0 sd 3:0:0:0: Attached scsi generic sg2 type 0 ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: Processor [CPU2] (supports 8 throttling states) ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126] input: Power Button (FF) as /class/input/input2 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input3 ACPI: Power Button (CM) [PWRB] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 18 ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LNKD] -> GSI 18 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:05:00.0 to 64 sky2 0000:05:00.0: v1.20 addr 0xfe9fc000 irq 19 Yukon-EC (0xb6) rev 2 sky2 eth0: addr 00:15:f2:0f:3e:f6 i2c-adapter i2c-0: nForce2 SMBus adapter at 0x600 i2c-adapter i2c-1: nForce2 SMBus adapter at 0x700 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUB0] -> GSI 21 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:0b.0 to 64 ohci_hcd 0000:00:0b.0: OHCI Host Controller ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0b.0: irq 20, io mem 0xfebfe000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected ath_hal: module license 'Proprietary' taints kernel. ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUB2] -> GSI 20 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:0b.1 to 64 ehci_hcd 0000:00:0b.1: EHCI Host Controller ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:0b.1: debug port 1 PCI: cache line size of 128 is not supported by device 0000:00:0b.1 ehci_hcd 0000:00:0b.1: irq 21, io mem 0xfebffc00 ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 10 ports detected hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 wlan: 0.9.4 input: PC Speaker as /class/input/input4 forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61. ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LMAC] -> GSI 23 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:13.0 to 64 ath_pci: 0.9.4 FDC 0 is a post-1991 82077 Linux video capture interface: v2.00 logips2pp: Detected unknown logitech mouse model 89 saa7130/34: v4l2 driver version 0.2.14 loaded forcedeth 0000:00:13.0: ifname eth1, PHY OUI 0x5043 @ 11, addr 00:15:f2:0f:44:d2 forcedeth 0000:00:13.0: highdma csum timirq gbit lnktim desc-v3 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 17 ACPI: PCI Interrupt 0000:06:06.0[A] -> Link [LNKA] -> GSI 17 (level, low) -> IRQ 22 usb 1-4: new full speed USB device using ohci_hcd and address 2 input: ImExPS/2 Logitech Explorer Mouse as /class/input/input5 parport_pc 00:06: reported by Plug and Play ACPI parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] ath_rate_sample: 1.2 (0.9.4) wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: H/W encryption support: WEP AES AES_CCM TKIP wifi0: mac 7.9 phy 4.5 radio 5.6 wifi0: Use hw queue 1 for WME_AC_BE traffic wifi0: Use hw queue 0 for WME_AC_BK traffic wifi0: Use hw queue 2 for WME_AC_VI traffic wifi0: Use hw queue 3 for WME_AC_VO traffic wifi0: Use hw queue 8 for CAB traffic wifi0: Use hw queue 9 for beacons wifi0: Atheros 5212: mem=0xfeaf0000, irq=22 ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 16 ACPI: PCI Interrupt 0000:06:0b.0[A] -> Link [LNKC] -> GSI 16 (level, low) -> IRQ 23 ACPI: PCI Interrupt Link [LACI] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LACI] -> GSI 22 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:0d.0 to 64 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[23] MMIO=[feaef000-feaef7ff] Max Packet=[2048] IR/IT contexts=[4/8] usb 1-4: configuration #1 chosen from 1 choice intel8x0_measure_ac97_clock: measured 58740 usecs intel8x0: clocking to 46992 ACPI: PCI Interrupt 0000:06:07.0[A] -> Link [LNKB] -> GSI 19 (level, low) -> IRQ 18 saa7133[0]: found at 0000:06:07.0, rev: 209, irq: 18, latency: 64, mmio: 0xfeaef800 saa7133[0]: subsystem: 11bd:002f, board: Pinnacle PCTV 40i/50i/110i (saa7133) [card=77,insmod option] saa7133[0]: board init: gpio is 600e000 input: Pinnacle PCTV as /class/input/input6 Bluetooth: Core ver 2.11 hci_usb: Unknown symbol hci_suspend_dev hci_usb: Unknown symbol hci_free_dev hci_usb: Unknown symbol hci_resume_dev hci_usb: Unknown symbol hci_alloc_dev hci_usb: Unknown symbol hci_unregister_dev hci_usb: Unknown symbol hci_recv_fragment hci_usb: Unknown symbol hci_register_dev hci_usb: Unknown symbol hci_suspend_dev hci_usb: Unknown symbol hci_free_dev hci_usb: Unknown symbol hci_resume_dev hci_usb: Unknown symbol hci_alloc_dev hci_usb: Unknown symbol hci_unregister_dev hci_usb: Unknown symbol hci_recv_fragment hci_usb: Unknown symbol hci_register_dev ir-kbd-i2c: Pinnacle PCTV detected at i2c-2/2-0047/ir0 [saa7133[0]] NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized saa7133[0]: i2c eeprom 00: bd 11 2f 00 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[0]: i2c eeprom 10: ff e0 60 06 ff 20 ff ff 00 30 8d 2e b2 c5 ff ff saa7133[0]: i2c eeprom 20: 01 2c 01 23 23 01 04 30 98 ff 00 e7 ff 21 00 c2 saa7133[0]: i2c eeprom 30: 96 10 03 32 15 20 ff 15 0e 6c a3 eb 03 dc d7 d9 saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Bluetooth: HCI USB driver ver 2.9 usbcore: registered new interface driver hci_usb tuner 2-004b: chip found @ 0x96 (saa7133[0]) tda8290 2-004b: setting tuner address to 61 tuner 2-004b: type set to tda8290+75a tda8290 2-004b: setting tuner address to 61 tuner 2-004b: type set to tda8290+75a saa7133[0]: registered device video0 [v4l2] saa7133[0]: registered device vbi0 saa7133[0]: registered device radio0 saa7134 ALSA driver for DMA sound loaded saa7133[0]/alsa: saa7133[0] at 0xfeaef800 irq 18 registered as card -1 BUG: unable to handle kernel NULL pointer dereference at virtual address 00000002 printing eip: f971f5d5 *pde = 00000000 Oops: 0000 [#1] SMP Modules linked in: saa7134_alsa tuner tea5767 tda8290 tuner_simple mt20xx tea5761 hci_usb bluetooth wlan_scan_sta ath_rate_sample snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm_oss snd_seq_dummy snd_seq_oss saa7134 snd_mpu401 snd_mpu401_uart compat_ioctl32 snd_seq_midi_event snd_rawmidi videobuf_dma_sg snd_seq videobuf_core ir_kbd_i2c snd_seq_device parport_pc snd_mixer_oss parport ir_common analog videodev snd_pcm gameport ohci1394 v4l2_common floppy v4l1_compat ath_pci ieee1394 forcedeth snd_timer pcspkr psmouse wlan snd ide_cd serio_raw ath_hal(P) soundcore cdrom snd_page_alloc ehci_hcd ohci_hcd usbcore i2c_nforce2 ssb i2c_core pcmcia pcmcia_core firmware_class sky2 thermal button processor sg evdev fuse reiserfs ata_generic sata_sil24 sata_nv pata_acpi pata_amd libata sd_mod scsi_mod ide_disk ide_generic generic amd74xx ide_core Pid: 4183, comm: modprobe Tainted: P (2.6.24-std-def-alt6 #1) EIP: 0060:[<f971f5d5>] EFLAGS: 00010246 CPU: 0 EIP is at snd_pcm_timer_init+0x25/0x170 [snd_pcm] EAX: 00000002 EBX: f72f26d8 ECX: f71bfde4 EDX: 00000000 ESI: f72f28a8 EDI: f705d564 EBP: 00000018 ESP: f71bfdcc DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 Process modprobe (pid: 4183, ti=f71be000 task=f76300f0 task.ti=f71be000) Stack: 00000000 00000001 f7729cd0 00000000 f7729cd0 00000000 00000003 00000000 f72f26d8 00000018 f96061fc 00000000 f72f28a8 f705d530 f9717687 f97287ac f705d530 f71bfe24 f7d5c34c 00000001 f705d534 f972042c 436d6370 63304432 Call Trace: [<f96061fc>] snd_add_device_sysfs_file+0x3c/0x70 [snd] [<f9717687>] snd_pcm_dev_register+0xe7/0x210 [snd_pcm] [<f960ad2d>] snd_device_register_all+0x2d/0x60 [snd] [<f9606a0e>] snd_card_register+0xe/0x2c0 [snd] [<f97f130a>] alsa_device_init+0x23a/0x280 [saa7134_alsa] [<f97f1399>] saa7134_alsa_init+0x49/0x80 [saa7134_alsa] [<c0152671>] sys_init_module+0x151/0x19e0 [<c017df9a>] __do_fault+0x21a/0x410 [<f971f910>] snd_pcm_format_width+0x0/0x20 [snd_pcm] [<c0195a50>] do_sync_read+0x0/0x120 [<c0105392>] sysenter_past_esp+0x6b/0xa9 ======================= Code: 5b c3 8d 74 26 00 56 89 c6 53 83 ec 30 8b 56 30 c7 44 24 1c 00 00 00 00 8d 4c 24 18 c7 44 24 18 03 00 00 00 8b 18 83 e2 01 8b 03 <8b> 00 89 44 24 20 8b 43 0c 89 44 24 24 8b 46 0c 01 c0 09 c2 8d EIP: [<f971f5d5>] snd_pcm_timer_init+0x25/0x170 [snd_pcm] SS:ESP 0068:f71bfdcc ---[ end trace 79d2bd57fb5b7511 ]--- ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d8000070acb1] Bluetooth: L2CAP ver 2.9 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 Adding 1566328k swap on /dev/sda2. Priority:-1 extents:1 across:1566328k nvidiafb_probe START ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 17 (level, low) -> IRQ 22 PCI: Unable to reserve mem region #2:8000000@d0000000 for device 0000:01:00.0 nvidiafb: cannot request PCI regions device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com ReiserFS: sda6: found reiserfs format "3.6" with standard journal ReiserFS: sda6: using ordered data mode ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda6: checking transaction log (sda6) ReiserFS: sda6: Using r5 hash to sort names ReiserFS: sdb1: found reiserfs format "3.6" with standard journal ReiserFS: sdb1: using ordered data mode ReiserFS: sdb1: journal params: device sdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sdb1: checking transaction log (sdb1) ReiserFS: sdb1: Using r5 hash to sort names ReiserFS: sdb2: found reiserfs format "3.6" with standard journal ReiserFS: sdb2: using ordered data mode ReiserFS: sdb2: journal params: device sdb2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sdb2: checking transaction log (sdb2) ReiserFS: sdb2: Using r5 hash to sort names it87: Found IT8712F chip at 0xd00, revision 7 it87: in3 is VCC (+5V) it87: in7 is VCCH (+5V Stand-By) BUG: unable to handle kernel NULL pointer dereference at virtual address 00000002 printing eip: f9719c51 *pde = 00000000 Oops: 0000 [#2] SMP Modules linked in: it87 hwmon_vid hwmon eeprom wlan_wep dm_mod nvidiafb fb_ddc i2c_algo_bit vgastate rfcomm l2cap saa7134_alsa tuner tea5767 tda8290 tuner_simple mt20xx tea5761 hci_usb bluetooth wlan_scan_sta ath_rate_sample snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm_oss snd_seq_dummy snd_seq_oss saa7134 snd_mpu401 snd_mpu401_uart compat_ioctl32 snd_seq_midi_event snd_rawmidi videobuf_dma_sg snd_seq videobuf_core ir_kbd_i2c snd_seq_device parport_pc snd_mixer_oss parport ir_common analog videodev snd_pcm gameport ohci1394 v4l2_common floppy v4l1_compat ath_pci ieee1394 forcedeth snd_timer pcspkr psmouse wlan snd ide_cd serio_raw ath_hal(P) soundcore cdrom snd_page_alloc ehci_hcd ohci_hcd usbcore i2c_nforce2 ssb i2c_core pcmcia pcmcia_core firmware_class sky2 thermal button processor sg evdev fuse reiserfs ata_generic sata_sil24 sata_nv pata_acpi pata_amd libata sd_mod scsi_mod ide_disk ide_generic generic amd74xx ide_core Pid: 5882, comm: hald Tainted: P D (2.6.24-std-def-alt6 #1) EIP: 0060:[<f9719c51>] EFLAGS: 00010246 CPU: 1 EIP is at snd_pcm_info+0x31/0x100 [snd_pcm] EAX: 00000002 EBX: f72f26d8 ECX: 00000040 EDX: f7203530 ESI: f72f28a8 EDI: f7203650 EBP: f7203530 ESP: f60f1e98 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 Process hald (pid: 5882, ti=f60f0000 task=f765acf0 task.ti=f60f0000) Stack: 00000001 f7203530 f6621c20 f72f28a8 f6621b78 f9716d24 c0191a6c f960858a f6621c20 f7515ad8 f7515aa8 f9716e90 f9608449 f7d94448 01008001 ffffffff f7515a10 00000000 f6974d98 f7d94448 c01cbbc6 f7d94448 f6974d98 00000000 Call Trace: [<f9716d24>] snd_pcm_proc_info_read+0x34/0x190 [snd_pcm] [<c0191a6c>] kmem_cache_alloc+0x8c/0x110 [<f960858a>] snd_info_entry_open+0x24a/0x290 [snd] [<f9716e90>] snd_pcm_stream_proc_info_read+0x0/0x10 [snd_pcm] [<f9608449>] snd_info_entry_open+0x109/0x290 [snd] [<c01cbbc6>] proc_reg_open+0x46/0x70 [<c0193ff5>] __dentry_open+0xc5/0x1d0 [<c01941b5>] nameidata_to_filp+0x35/0x40 [<c01cbb80>] proc_reg_open+0x0/0x70 [<c0194210>] do_filp_open+0x50/0x60 [<c0193ea2>] get_unused_fd_flags+0x52/0xd0 [<c019426c>] do_sys_open+0x4c/0xf0 [<c019434c>] sys_open+0x1c/0x20 [<c0105392>] sysenter_past_esp+0x6b/0xa9 ======================= Code: 00 00 89 74 24 08 89 c6 89 7c 24 0c 89 d7 89 6c 24 10 89 d5 89 5c 24 04 8b 18 8b 40 04 89 04 24 31 c0 f3 ab 8b 03 b9 40 00 00 00 <8b> 00 89 42 0c 8b 43 0c 89 02 8b 46 30 89 42 08 8b 46 0c 89 42 EIP: [<f9719c51>] snd_pcm_info+0x31/0x100 [snd_pcm] SS:ESP 0068:f60f1e98 ---[ end trace 79d2bd57fb5b7511 ]--- hdc: UDMA/66 mode selected Linux agpgart interface v0.102 PCI: Setting latency timer of device 0000:01:00.0 to 64 NVRM: loading NVIDIA UNIX x86 Kernel Module 169.12 Thu Feb 14 17:53:07 PST 2008 Pinnacle PCTV: unknown key: key=0x35 raw=0x35 down=1 Pinnacle PCTV: unknown key: key=0x35 raw=0x35 down=0
во-первых не стоит множество проблем сваливать в одну багу, так не удобно разбираться. во-вторых я вижу тут только 1 проблему из 3х(или 2х) c saa7134-alsa. bluetooth дальше вроде загрузился, он работает? в чём проблема проблема с ACPI?
Относительно вот этого ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.LSTA] (Node f7c34cd0), AE_TYPE ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.LATA._STA] (Node f7c36d60), AE_TYPE ACPI Error (uteval-0233): Method execution failed [\_SB_.LATA._STA] (Node f7c36d60), AE_TYPE могу сказать, что во время первой загрузки ядра весь процесс просто повис на стадии создания устройств в /dev. Последующая перезагрузка такого не проявила. Собственно, это связать с чем-то кроме вышеприведенного куска не могу.
с saa7134-alsa есть подозрение что проблема в pcm.h, который разный в ядре и в alsa. Такое ощущение, что часть модулей собрано с другим struct snd_pcm
Проблема решаена в alt7
